Wholesale Sourcing

Wholesale Sourcing Trade Show Sample: What the Quote Actually Covers - HOLYCOME

Wholesale Sourcing Trade Show Sample: What the Quote Actually Covers - HOLYCOME

SECTION 01Trade Show Sampling for wholesale Sourcing

A trade show converts on the sample that leaves the booth, not on the catalogue that gets left behind. The sample card has to carry the model number, the metal, the stone size, the FOB price and the MOQ, or the follow-up email starts from zero, and at USD 41-231 for 100 pieces that is the number the buyer signs.

Ten to twelve pieces on a tray is the useful number for wholesale Sourcing. More than that and the buyer photographs instead of touching, and a photograph is not an order, which is USD 41-231 on the Trade Show Sample schedule.

Wholesale Sourcing wholesale piece from the HOLYCOME line in Wuzhou

The follow-up window is seven days. After that the card sits in a stack. We write the quote the same week and put the sample in the post so the buyer has the piece on the desk when the price arrives, and at USD 41-231 for 100 pieces that is the number the buyer signs.

SECTION 02What the Quote Actually Covers

Last February, a US buyer of wholesale Sourcing placed 100 wholesale Sourcing against a sample signed in June. The first container landed with 9 pieces that failed on prong geometry alone, and USD 30-85 landed on the buyer's P&L before a single unit sold, which is how the Trade Show Sample account reads it at USD 41-231.

On a 100-piece order at USD 41-231, a prong geometry rate above two percent is not a quality surprise. It is a costing error that shows up as a credit note three weeks later.

Nothing in the rebuild was expensive. A gauge, a written limit and a retained tray did the work that a discount would only have delayed, quoted at USD 41-231 per piece in display tray with sample card.

Wholesale Sourcing setting and finish detail on a HOLYCOME factory sample

SECTION 03What US buyers Check Before They Sign

At USD 41-231 per piece the four measurements below are worth more than the discount being negotiated. One of them costs nothing to write down.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Stone colour consistencyGraded by eye under D65Colour matched to a retained master stone, per trayRepeat colour complaint in the same SKU
Sizing drift across the runNot measuredGo/no-go gauge on every size, drift held under 0.15 mmResize queue and reship cost
Clasp spring lifeSampled by handCycled 500 times on a jig per lotDetach claim and brand damage
Prong tension and seat depthChecked by feel at the benchPull-tested per piece, seat depth written on the sheetStone loss and total replacement

Write these into the Trade Show Sample purchase order and the arrival check becomes arithmetic instead of recollection, shipped as display tray with sample card and certified GRA report.

SECTION 04Where USD 41-231 Per Piece Actually Goes

Cost at USD 41-231 leaves no room for assumption. The table shows which line compresses and which line only moves quality down.

Cost lineShareWhat moves it
Base metal or alloy for wholesale Sourcing30%Alloy choice and casting yield
Stone or melee for wholesale Sourcing20%Sieve range and lot batching
Setting and finishing labor for wholesale Sourcing19%Jig design and bench minutes
Plating, polish and QC for wholesale Sourcing12%Per-tray versus per-piece checks
Packaging for wholesale Sourcing19%display tray with sample card

A factory that cannot state its bench minutes per piece has never costed its own line. Ask for minutes and for the reject rule, not for a discount, and at USD 41-231 for 100 pieces that is the number the buyer signs.

SECTION 05What the Quote Actually Covers

This is the question that separates a trading company from a factory, and on wholesale Sourcing the answer is usually shorter than buyers expect, certified GRA report and packed display tray with sample card at 100 pieces.

The commercial version of this question for wholesale Sourcing is simple: what does a failure cost the buyer, and who pays it. In our terms the answer is a replacement inside the same order cycle, with the retained reference tray as the arbiter, priced at USD 41-231 for the 100-piece Trade Show Sample run.

That clause matters more than a discount on wholesale Sourcing. A 4% lower unit price disappears on the first rejected tray; a written responsibility clause does not, quoted at USD 41-231 per piece in display tray with sample card.

SECTION 06MOQ, Mixed Designs and the Real First Order

Buyers ask it in the first call about wholesale Sourcing and rarely get a number they can put in a spreadsheet, quoted at USD 41-231 per piece in display tray with sample card.

What buyers underestimate on wholesale Sourcing is the cost of the interruption, not the cost of the piece. A missing 6% of a run stalls a launch, and a stalled launch costs more than the 6% ever did, priced at USD 41-231 for the 100-piece Trade Show Sample run.

We plan a 3-5% buffer on first runs of wholesale Sourcing and tell the buyer it exists. Hiding a buffer and shipping it as production is how a supplier trains a buyer to distrust the count, which is USD 41-231 on the Trade Show Sample schedule.

SECTION 07Order Terms, Sample Timing and Packing

The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 100-piece Trade Show Sample order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, which the Trade Show Sample file records at USD 41-231 in display tray with sample card.

Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 41-231 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.

Packing follows the display tray with sample card format at 100 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, on a 100-piece Trade Show Sample order at USD 41-231.

Certification is GRA report for the lots that carry it, with a batch report and per-piece measurement of stone retention after a 40-cycle wear test for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, with GRA report and display tray with sample card stated on the same sheet.

A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, and 100 pieces leaves Wuzhou in display tray with sample card at USD 41-231.

SECTION 08The Three Failures We See Most in Incoming Samples

rhodium burn-off

A 0.05 micron rhodium layer reads white in the tray and shows yellow at the shank in six months of daily wear. Thickness, not bath chemistry, is the variable that matters, the figure being USD 41-231 for a 100-piece run.

In a 100-piece run this typically shows on 14 of pieces. Catching it means measuring stone retention after a 40-cycle wear test at the tray level, not inspecting the finished carton, and the Trade Show Sample quote for it sits at USD 41-231.

size-step drift

A run gauged at size 6 and estimated elsewhere ships a size 8 that measures 7.75. The mismatch shows up as a resize queue two weeks after launch, which is how the Trade Show Sample account reads it at USD 41-231.

The commercial effect is a return shipment plus a resize labor claim, typically USD 9-14 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, shipped as display tray with sample card and certified GRA report.

prong geometry

A prong that grips the girdle instead of the pavilion survives the showroom and fails the third ultrasonic clean. The seat has to be cut to the pavilion angle before the prongs close, which is USD 41-231 on the Trade Show Sample schedule.

Our countermeasure is a gauge and a written limit. It adds about 22 seconds per piece and removes the defect from the run rather than from the carton, with GRA report and display tray with sample card stated on the same sheet.

SECTION 09What This Means for a First Order

A first Trade Show Sample order of 50 pieces per design at USD 41-231 tests the line rather than the range. Three designs covers the shelf.

Ask for the retained tray and the GRA report batch sheet with the first shipment. Both are free and both decide the reorder, which is how the Trade Show Sample account reads it at USD 41-231.

SECTION 10How a Repeat Order Gets Built

Nothing in this sequence is unusual, and that is the point. Each step exists because skipping it produced a specific failure on a previous order, which is USD 41-231 on the Trade Show Sample schedule.

  1. Lock the spec: metal, stone size range, plating thickness, sizing band and finish, all written on one sheet.
  2. Pull a stock-component sample in 3-5 days and measure it against that sheet, not against the photo.
  3. Approve the sample in writing, including the reject rule and the retained reference tray.
  4. Run bulk in 15-20 days for orders under 500 pieces, with the gauge check independent of the shift.
  5. Ship from Guangzhou or Shenzhen with the QC sheet in the carton and the batch report by email.

Reorders inside this sequence run 12-15 days because the model, the gauge set and the signed spec stay in our system, on a 100-piece Trade Show Sample order at USD 41-231.

SECTION 11Freight, Duty and the Arrival Check

Export runs through Guangzhou or Shenzhen. Air lands in 5-8 days on the US west coast, 7-10 on the east, and sea takes roughly three times the transit, with GRA report and display tray with sample card stated on the same sheet, on a 100-piece Trade Show Sample order at USD 41-231.

FOB is the default on wholesale Sourcing and DDP is the option. Buyers new to US wholesale usually take DDP once, then switch after they see the breakdown, priced at USD 41-231 for the 100-piece Trade Show Sample run.

If prong geometry appears in the arrival check, the retained tray decides who owns it. Keep the GRA report batch sheet in the same folder as the packing list, the figure being USD 41-231 for a 100-piece run.

SECTION 12Frequently Asked Questions

How do you handle a rejected tray?

We replace or credit inside the same order cycle. The retained reference tray decides: if prong geometry shows on our retained piece we own it, and if it appeared in transit we split the assay cost and file with the carrier, which the Trade Show Sample file records at USD 41-231 in display tray with sample card.

What are the payment terms?

30 percent deposit with the order, 70 percent against the bill of lading. For accounts on a second order we quote 30/70 with a 15-day balance window once the first shipment has cleared, which the Trade Show Sample file records at USD 41-231 in display tray with sample card.

What is the minimum order for wholesale Sourcing?

50 pieces per wholesale Sourcing. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 the gauge check stops being independent of the shift, with GRA report and display tray with sample card stated on the same sheet.

Do you supply certificates for wholesale Sourcing?

GRA report on wholesale Sourcing above the threshold stated on the quote. Below it we supply a batch report plus per-piece measurement of stone retention after a 40-cycle wear test, which is what a counter or a listing actually needs, and at USD 41-231 for 100 pieces that is the number the buyer signs.

How do you handle a rejected tray?

We replace or credit inside the same order cycle. The retained reference tray decides: if prong geometry shows on our retained piece we own it, and if it appeared in transit we split the assay cost and file with the carrier, which the Trade Show Sample file records at USD 41-231 in display tray with sample card.

SECTION 13Next Step

The next step is a sample in 3-5 days, not a container. Write to service@holycome.com or WhatsApp +86 18078079070, subject Trade Show Sample, priced at USD 41-231 for the 100-piece Trade Show Sample run.

HOLYCOME is operated by Wuzhou HengliLai Jewelry Co., Ltd., a factory in Wuzhou, Guangxi, producing since 2009 at roughly 60,000 pieces a month. Contact service@holycome.com or WhatsApp +86 18078079070, certified GRA report and packed display tray with sample card at 100 pieces.

Related reading: Wholesale Sourcing Q4 Holiday Stock: MOQ, Mixed Designs and the Real First Order - HOLYCOME Certification Explained Bridal Boutique: How the Second Order Becomes Cheaper - HOLYCOME

E

Editorial Team

Senior editor at HOLYCOME, specializing in gemstone identification, jewelry manufacturing, and wholesale sourcing guides.

Looking for Wholesale Jewelry?

Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.

Contact on WhatsApp service@holycome.com

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .