In July, a US buyer of wholesale Sourcing ordered 200 wholesale Sourcing and asked for the same lost-wax cast as a competitor's sample. What arrived matched the photo and missed the drawing, and 13 pieces had to be reworked at the buyer's expense, and the Private Label Carton quote for it sits at USD 45-252.
Nothing in that rejection was exotic. At USD 45-252 per piece and 200 pieces on the order, a prong geometry rate of two percent is a costing error rather than a quality mystery.
Cost of the fix was about 22 seconds per piece. On 200 pieces that is a few hours at the bench and the whole claim file disappears, on a 200-piece Private Label Carton order at USD 45-252.
Four numbers separate a 200-piece run that clears inspection from one that generates a credit note. None of them appears on the sample photo, certified GRA report and packed private-label carton with hangtag at 200 pieces.
| Spec point | Common trade output | HOLYCOME standard | Cost if missed |
|---|---|---|---|
| Stone colour consistency | Graded by eye under D65 | Colour matched to a retained master stone, per tray | Repeat colour complaint in the same SKU |
| Sizing drift across the run | Not measured | Go/no-go gauge on every size, drift held under 0.15 mm | Resize queue and reship cost |
| Clasp spring life | Sampled by hand | Cycled 500 times on a jig per lot | Detach claim and brand damage |
| Prong tension and seat depth | Checked by feel at the bench | Pull-tested per piece, seat depth written on the sheet | Stone loss and total replacement |
None of these are premium features. They cost seconds per piece and they remove the reason a buyer has to inspect twice, which the Private Label Carton file records at USD 45-252 in private-label carton with hangtag.
Private label changes four things and none of them is the piece: the stamp, the hangtag, the box and the barcode. Get those four aligned before the first bulk run or the carton arrives with your name spelled two ways, the figure being USD 45-252 for a 200-piece run.
The stamp goes inside the shank or on the clasp tag, and it has to be small enough not to break the surface on a thin wholesale Sourcing. Below 0.8 mm of shank width we recommend the hangtag only, on a 200-piece Private Label Carton order at USD 45-252.
Cartons are quoted at 200 pieces with the label printed, not stickered, because a sticker on a matte box reads as a repack. Lead time adds three days for the print run, which is why private label starts later than stock, which is USD 45-252 on the Private Label Carton schedule.
The cost of a wholesale Sourcing in the USD 45-252 band splits roughly as below. The line buyers challenge most is labor, and it is the line that decides whether the piece survives a season.
| Cost line | Share | What moves it |
|---|---|---|
| Base metal or alloy for wholesale Sourcing | 34% | Alloy choice and casting yield |
| Stone or melee for wholesale Sourcing | 25% | Sieve range and lot batching |
| Setting and finishing labor for wholesale Sourcing | 22% | Jig design and bench minutes |
| Plating, polish and QC for wholesale Sourcing | 15% | Per-tray versus per-piece checks |
| Packaging for wholesale Sourcing | 4% | private-label carton with hangtag |
If a supplier will not break out the five lines above, the number you are comparing is not a price. It is a total that somebody else assembled from assumptions, certified GRA report and packed private-label carton with hangtag at 200 pieces, which the Private Label Carton file records at USD 45-252 in private-label carton with hangtag.
A run gauged at size 6 and estimated elsewhere ships a size 8 that measures 7.75. The mismatch shows up as a resize queue two weeks after launch, priced at USD 45-252 for the 200-piece Private Label Carton run.
Our countermeasure is a gauge and a written limit. It adds about 22 seconds per piece and removes the defect from the run rather than from the carton, and at USD 45-252 for 200 pieces that is the number the buyer signs.
A prong that grips the girdle instead of the pavilion survives the showroom and fails the third ultrasonic clean. The seat has to be cut to the pavilion angle before the prongs close, the figure being USD 45-252 for a 200-piece run.
In a 200-piece run this typically shows on 17 of pieces. Catching it means measuring stone retention after a 40-cycle wear test at the tray level, not inspecting the finished carton, and the Private Label Carton quote for it sits at USD 45-252.
A 0.05 micron rhodium layer reads white in the tray and shows yellow at the shank in six months of daily wear. Thickness, not bath chemistry, is the variable that matters, which the Private Label Carton file records at USD 45-252 in private-label carton with hangtag.
The commercial effect is a return shipment plus a resize labor claim, typically USD 9-14 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, quoted at USD 45-252 per piece in private-label carton with hangtag.
The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 200-piece Private Label Carton order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, and 200 pieces leaves Wuzhou in private-label carton with hangtag at USD 45-252.
Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 45-252 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.
Packing follows the private-label carton with hangtag format at 200 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, the figure being USD 45-252 for a 200-piece run.
Certification is GRA report for the lots that carry it, with a batch report and per-piece measurement of stone retention after a 40-cycle wear test for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, and at USD 45-252 for 200 pieces that is the number the buyer signs.
A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, with GRA report and private-label carton with hangtag stated on the same sheet.
The figure below is what we quote for wholesale Sourcing, and it is deliberately narrower than the market average, quoted at USD 45-252 per piece in private-label carton with hangtag.
The commercial version of this question for wholesale Sourcing is simple: what does a failure cost the buyer, and who pays it. In our terms the answer is a replacement inside the same order cycle, with the retained reference tray as the arbiter, which is USD 45-252 on the Private Label Carton schedule.
That clause matters more than a discount on wholesale Sourcing. A 4% lower unit price disappears on the first rejected tray; a written responsibility clause does not, and 200 pieces leaves Wuzhou in private-label carton with hangtag at USD 45-252.
Most wholesale Sourcing disputes we arbitrate trace back to this line, not to the defect itself, quoted at USD 45-252 per piece in private-label carton with hangtag.
We run this check per tray rather than per carton because the defect that matters on wholesale Sourcing is the one that repeats. A single odd piece is noise; a pattern across one tray is a process problem and it will be in every tray made after it, certified GRA report and packed private-label carton with hangtag at 200 pieces.
The report the buyer receives states the count per tray, the measured average and the outlier count for wholesale Sourcing. It is deliberately unglamorous, and it is the document that settles most disputes before they start, which is how the Private Label Carton account reads it at USD 45-252.
The calendar below is what we quote on a 200-piece Private Label Carton run of wholesale Sourcing. It starts when the spec is signed, not when the deposit clears, quoted at USD 45-252 per piece in private-label carton with hangtag.
A first order of 50 pieces is a measurement, not a purchase. It tells you what stone retention after a 40-cycle wear test looks like from this bench, shipped as private-label carton with hangtag and certified GRA report, which is USD 45-252 on the Private Label Carton schedule.
At 200 pieces inside private-label carton with hangtag, the first order reads sell-through without betting the season on one model, which the Private Label Carton file records at USD 45-252 in private-label carton with hangtag.
Buyers who run that measurement before committing a season usually keep the supplier. Buyers who skip it usually pay twice for the same lesson, priced at USD 45-252 for the 200-piece Private Label Carton run.
We ship from Guangzhou or Shenzhen and pick the port on the carrier rate, not on habit. GRA report travels with the shipping documents, and the Private Label Carton quote for it sits at USD 45-252.
DDP removes the duty invoice that arrives after the carton clears, which matters on a first Private Label Carton order at USD 45-252.
Three steps at the dock: count against the packing list, weigh a sample tray, measure ten pieces. None needs a lab, on a 200-piece Private Label Carton order at USD 45-252.
50 pieces per wholesale Sourcing. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 the gauge check stops being independent of the shift, and at USD 45-252 for 200 pieces that is the number the buyer signs.
GRA report on wholesale Sourcing above the threshold stated on the quote. Below it we supply a batch report plus per-piece measurement of stone retention after a 40-cycle wear test, which is what a counter or a listing actually needs, certified GRA report and packed private-label carton with hangtag at 200 pieces.
We replace or credit inside the same order cycle. The retained reference tray decides: if prong geometry shows on our retained piece we own it, and if it appeared in transit we split the assay cost and file with the carrier, and the Private Label Carton quote for it sits at USD 45-252.
30 percent deposit with the order, 70 percent against the bill of lading. For accounts on a second order we quote 30/70 with a 15-day balance window once the first shipment has cleared, and the Private Label Carton quote for it sits at USD 45-252.
50 pieces per wholesale Sourcing. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 the gauge check stops being independent of the shift, and at USD 45-252 for 200 pieces that is the number the buyer signs.
If you are quoting wholesale Sourcing against another supplier, send that quote. We will mark the four lines where the numbers diverge and let you decide, and the Private Label Carton quote for it sits at USD 45-252.
The factory behind wholesale Sourcing here is Wuzhou HengliLai Jewelry Co., Ltd., operating since 2009 in Wuzhou, Guangxi, at roughly 60,000 pieces a month. Reach the export desk at service@holycome.com or +86 18078079070 on WhatsApp, on a 200-piece Private Label Carton order at USD 45-252.
Related reading: Wholesale Sourcing Vermeil Upgrade: Alloy, Karat and the Cost of a Color Change - HOLYCOME Wholesale Sourcing Valentine Program: Sample to Container: The Real Calendar - HOLYCOME
Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.
Contact on WhatsApp service@holycome.comWritten by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.
Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.
Reviewed for accuracy by our quality team before publication. Last updated .