A distributor in Santiago accepted a credit note and lost the season because a credit does not restock a shelf. The order was not lost on price. It was lost on a specification nobody wrote down. This piece looks at wholesale sourcing from the buyer's side of the table: what the promise means at the bench, what it costs to get it wrong, and how to write a brief a factory can be held to.
A defect claim is a logistics problem before it is a commercial one. Without a lot reference, a photograph and a count, a factory can only argue, and arguing costs the season.
We settle on replacement first, credit second, because the shelf needs a piece and not a number.
The default offer in this category is a stock photo, a unit price and a thirty-day promise. That works for one order and stops working on the second, because a stock photo cannot specify tennis lines.
| Comparison | Common practice | What we hold | Why it matters |
|---|---|---|---|
| Claim input | Weak | Effective | |
| Reference | "broken" | lot and rack number | |
| Evidence | description | photo at 10x plus scale | |
| Count | estimate | per-piece count | |
| Remedy | credit note | replacement in 10 days |
Clasp fatigue cycles to 5,000 open-close is the number we publish per lot. It is the one a buyer can check with a caliper and a loupe in ten minutes, and the one that decides whether a reorder is a formality or a negotiation.
At the receiving table: count per SKU against the packing list, weigh three pieces, measure the bracelet, check one stone at 10x for seat and tilt, and confirm the plating colour against an approved sample.
Five checks, ten minutes. They catch the defects that are visible on day one and free the buyer to argue about the ones that are not, with evidence rather than impression.
Read the specification as a checklist: tennis lines, bangles and chain bracelets at 6.5/7/7.5 inch with box or fold-over clasp. Each comma is a decision someone made, and each decision has a cheaper alternative that a factory can substitute without telling you.
The substitution is usually invisible on delivery. It shows up as a hue shift in month three, a prong that will not hold after a resize, or a plating that reads slightly warm under store lighting.
We measure clasp fatigue cycles to 5,000 open-close on every lot and record the number against the rack. It is the one figure a buyer can independently verify with a caliper, a loupe and ten minutes at the receiving table.
If the number is inside the band, the lot ships. If it is outside, it goes back to the bench rather than into a carton with a note that says the buyer should expect variation.
A returned bracelet costs the unit price twice: once in goods, once in handling, plus the freight both ways and the customer's lost confidence. On a bracelet the handling is usually larger than the margin.
That is the arithmetic behind every decision on this page. A cent saved on plating is not a saving if it produces a return rate two points higher.
We inspect at AQL 2.5 on the final line and 3 to 5 per cent on setting, sampled per carton rather than per lot. Per-carton sampling is stricter because a defect that clusters in one carton is a process problem, not a random one.
Anything above the AQL is held and reworked before packing. We do not sort after arrival, because sorting after arrival is a cost the buyer pays and a defect the buyer discovers in front of a customer.
At the receiving table: count per SKU against the packing list, weigh three pieces, measure the bracelet, check one stone at 10x for seat and tilt, and confirm the plating colour against an approved sample.
Five checks, ten minutes. They catch the defects that are visible on day one and free the buyer to argue about the ones that are not, with evidence rather than impression.
A trial is not a small version of an order. It is a test of four things: whether the drawing survives production, whether the hue band lands where you approved it, whether the plating thickness holds, and whether the carton arrives saleable.
We run it as a normal lot, not a special one, because a trial produced on a different line tells you nothing about the line you will eventually buy from.
A specification is only useful if a bench worker can act on it. "Premium quality" cannot be acted on. "Four-prong basket, 1.2mm prong wire, stone seated within 0.02mm of the bearing surface" can be checked with a loupe in nine seconds.
We write at that level because that is the level where a defect is preventable. Every field on our sheet has an instrument behind it: a caliper, a loupe, a cross-section, a salt-spray chamber.
A commercial invoice, a packing list and a certificate of origin, and the three have to agree line for line. Customs does not fail on the goods, it fails on the description, and a finished piece declared under a loose-stone heading is the most common failure in this trade.
We issue the set with the finished-article classification and the composition on the invoice, and we quote freight on both actual and volumetric weight so the landed number you model is the one you pay.
A trial is not a small version of an order. It is a test of four things: whether the drawing survives production, whether the hue band lands where you approved it, whether the plating thickness holds, and whether the carton arrives saleable.
We run it as a normal lot, not a special one, because a trial produced on a different line tells you nothing about the line you will eventually buy from.
Fifty pieces per design is the working minimum on wholesale sourcing. A sample runs three to five days, bulk fifteen to twenty days under 500 pieces, and a custom mould twenty-five to thirty days from drawing approval. Payment is 30% deposit with the balance against the bill of lading copy.
If the order is below fifty, the setup cost per piece roughly doubles because the casting tree and the plating rack are fixed costs. That is arithmetic, not a policy to negotiate around.
| Item | Value | Note |
|---|---|---|
| MOQ | 50 pcs / design | sizes and colours can be split |
| Sample | 3-5 days | one piece, approved before the run |
| Bulk lead time | 15-20 days | under 500 pieces |
| Custom lead time | 25-30 days | from drawing approval |
| Payment | 30% / 70% | balance against B/L copy |
| Port | Guangzhou / Shenzhen | export from Wuzhou |
The lot reference, a photograph of the failure with a scale, and the count per SKU. With those we decide inside two working days.
Replace by default when the defect is ours and the season is live. Credit is for the end of a season or for a count too small to ship economically.
We do when the defect is above the agreed AQL. Below it, the buyer normally absorbs the return because the volume does not justify the freight.
Approve stones from a stated hue band, approve one plated sample per rack, and inspect ten pieces on arrival. Those three steps prevent most of what turns into a claim.
Yes, if we hold the four inputs: alloy batch, stone parcel, plating tank and setting team. The reorder sheet records all four, so the check happens against a document rather than against a memory.
Photograph the piece with a scale and reference the lot line. Above the agreed AQL we replace and cover freight; inside it we replace the affected units inside ten days.
HOLYCOME by Wuzhou HengliLai Jewelry Co., Ltd. runs casting, setting, polishing and plating on one site in Wuzhou, Guangxi, the artificial gemstone cluster that supplies most of the trade. Monthly capacity is roughly 60,000 pieces across silver and gold lines. Buyers can reach the trade desk at service@holycome.com or on WhatsApp at +86 18078079070, and a factory visit can be arranged with two weeks' notice.
If you are pricing wholesale sourcing for a season, send the quantity per design, the stone grade you need and the date you need it on the shelf. We will return a drawing, a landed cost and a production date within three days, and a physical sample before you commit to a run. Samples are charged at cost and credited against the first order.
Related reading: GIA Diamond Report: Every Section Explained, Payment Terms with Chinese Jewelry Factories, Sample Order Strategy for Jewelry Wholesale
Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.
Contact on WhatsApp service@holycome.comWritten by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.
Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.
Reviewed for accuracy by our quality team before publication. Last updated .