A retailer in Oslo asked for exclusive designs and received a recoloured version of a stock style and found it on a marketplace within a month. The order was not lost on price. It was lost on a specification nobody wrote down. This piece looks at trends & styles from the buyer's side of the table: what the promise means at the bench, what it costs to get it wrong, and how to write a brief a factory can be held to.
Private label is not a box and a tag. It is an exclusivity term, a design source, a packaging specification and a reorder guarantee, and all four have to be in writing.
We will not sell a design we made for you to another buyer. That is a contractual commitment, not a courtesy.
The default offer in this category is a stock photo, a unit price and a thirty-day promise. That works for one order and stops working on the second, because a stock photo cannot specify studs.
| Comparison | Common practice | What we hold | Why it matters |
|---|---|---|---|
| Element | Weak programme | What we contract | |
| Design | recoloured stock | new mould or documented variant | |
| Exclusivity | none | no resale of the design for 24 months | |
| Packaging | generic box | your dieline and barcode | |
| Reorder | price at will | price band locked 12 months |
Pair weight match within 0.02g is the number we publish per lot. It is the one a buyer can check with a caliper and a loupe in ten minutes, and the one that decides whether a reorder is a formality or a negotiation.
The carton is the first physical impression. An anti-tarnish pouch, a cavity insert and a stone-side-up orientation cost a few cents and prevent most of the transit damage we see on earrings.
Loose fill is the main cause of bent posts and scratched faces. It is cheaper than a cavity insert by about two cents a unit, which is the worst trade in the category.
Publishing pair weight match within 0.02g and the plating micron figure is uncomfortable for a factory that expects to be judged on photographs. It is comfortable for a buyer who has to defend a reorder to a boss.
The number is the argument. A supplier who will not publish one is asking you to trust the photograph instead.
On earrings the three failures that come back most often are post bending, back loss, and weight mismatch between the two stones in a pair. Each has a root cause upstream of the bench, which is why sorting finished pieces never fixes the rate.
Prong wear traces to wire gauge and setting pressure. Stone tilt traces to the bearing surface being cut by hand instead of by burr. Plating burn-off traces to rack contact points, not to the tank.
Tolerance compounds across operations. A casting that runs 0.15mm wide, a setting that shifts the stone 0.1mm, and a polish that removes 0.05mm of surface can put a pair of earrings outside the size the customer ordered without any single step being out of specification.
That is why we hold the stack at the casting rather than at the finish. Tightening the last operation cannot recover tolerance that was already spent at the first.
Every reorder comes back with the original sheet: alloy batch, stone parcel reference, plating rack number, setting team, measured pair weight match within 0.02g. It is four lines and it removes the argument about what "the same" means.
Buyers who keep those four lines can audit a fifth lot in an afternoon. Buyers who do not are comparing two photographs and hoping.
The carton is the first physical impression. An anti-tarnish pouch, a cavity insert and a stone-side-up orientation cost a few cents and prevent most of the transit damage we see on earrings.
Loose fill is the main cause of bent posts and scratched faces. It is cheaper than a cavity insert by about two cents a unit, which is the worst trade in the category.
We will not quote from a stock photo, we will not promise a date the plating queue cannot hold, and we will not sell a design we made exclusively for one buyer to another buyer.
Each of those is a short-term sale and a long-term loss, and the loss lands on the buyer who trusted the quote. Saying no to them is the cheapest quality control we operate.
A tolerance stated after the drawing is a complaint waiting to happen. State it before and it becomes a manufacturing instruction, which is a very different conversation at the bench.
Most disputes we see are not about quality. They are about two people who each thought the other had agreed to a number that nobody wrote down.
Repeatability depends on four inputs staying fixed: the alloy batch, the stone parcel, the plating tank and the setting team. Swap any one of them to save cost and the fifth lot looks like a different product to your customer.
We keep the lot record for all four, so a reorder is compared against your first lot rather than against a photograph on a website.
We will not quote from a stock photo, we will not promise a date the plating queue cannot hold, and we will not sell a design we made exclusively for one buyer to another buyer.
Each of those is a short-term sale and a long-term loss, and the loss lands on the buyer who trusted the quote. Saying no to them is the cheapest quality control we operate.
Fifty pieces per design is the working minimum on trends & styles. A sample runs three to five days, bulk fifteen to twenty days under 500 pieces, and a custom mould twenty-five to thirty days from drawing approval. Payment is 30% deposit with the balance against the bill of lading copy.
If the order is below fifty, the setup cost per piece roughly doubles because the casting tree and the plating rack are fixed costs. That is arithmetic, not a policy to negotiate around.
| Item | Value | Note |
|---|---|---|
| MOQ | 50 pcs / design | sizes and colours can be split |
| Sample | 3-5 days | one piece, approved before the run |
| Bulk lead time | 15-20 days | under 500 pieces |
| Custom lead time | 25-30 days | from drawing approval |
| Payment | 30% / 70% | balance against B/L copy |
| Port | Guangzhou / Shenzhen | export from Wuzhou |
Yes, with a new mould paid once and owned by you. We will not offer that design, or a variant within 1mm of its outline, to another buyer for twenty-four months.
Fifty pieces per design, with a minimum of four designs to justify a dedicated packaging run. Below four designs the dieline cost per SKU dominates.
Yes, including the country-of-origin mark, the karat hallmark and your SKU barcode. We will produce one labelled sample for legal review before the run.
We are, and we will say so on the customs paperwork. Some brands prefer to be named as the importer of record, which is a separate arrangement we can document.
Yes, if we hold the four inputs: alloy batch, stone parcel, plating tank and setting team. The reorder sheet records all four, so the check happens against a document rather than against a memory.
Photograph the piece with a scale and reference the lot line. Above the agreed AQL we replace and cover freight; inside it we replace the affected units inside ten days.
HOLYCOME by Wuzhou HengliLai Jewelry Co., Ltd. runs casting, setting, polishing and plating on one site in Wuzhou, Guangxi, the artificial gemstone cluster that supplies most of the trade. Monthly capacity is roughly 60,000 pieces across silver and gold lines. Buyers can reach the trade desk at service@holycome.com or on WhatsApp at +86 18078079070, and a factory visit can be arranged with two weeks' notice.
If you are pricing trends & styles for a season, send the quantity per design, the stone grade you need and the date you need it on the shelf. We will return a drawing, a landed cost and a production date within three days, and a physical sample before you commit to a run. Samples are charged at cost and credited against the first order.
Related reading: How to Spot a Fake Diamond Certificate, NGTC Certificate: China's Diamond Lab Explained, IGI Certification: What Buyers Should Know
Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.
Contact on WhatsApp service@holycome.comWritten by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.
Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.
Reviewed for accuracy by our quality team before publication. Last updated .