Direct Answer: an inspection on trends and styles only decides one thing, whether the lot matches the retained reference piece on the measurements written down before production. AQL tables decide how many pieces to pull; they do not decide what a piece is supposed to be. Write the spec first, then sample against it, and the argument after delivery becomes arithmetic.
The plan below is the sampling we apply on a 400-piece order. Pull the trends and styles before the trays are packed, not after, because a tray that has been wrapped is a tray nobody wants to unwrap.
| Lot size | Sample | Critical | Major | Minor |
|---|---|---|---|---|
| 50 to 150 pieces | 13 pieces | Zero | 2 | 3 |
| 151 to 500 pieces | 32 pieces | Zero | 3 | 5 |
| 501 to 1,200 pieces | 50 pieces | Zero | 5 | 7 |
| Over 1,200 pieces | 80 pieces | Zero | 7 | 10 |
A critical defect is stone loss, a broken prong, a clasp that opens under load, or metal that fails a nickel or lead screen. One piece stops the lot regardless of the lot size, because one piece is enough to generate the return, a detail that decides the reorder on trends and styles at USD 38-210.
Six stations sound like six costs. In practice the first three remove the reasons for the last three to reject anything, and the whole sequence adds a few minutes per tray rather than per piece, the same figure we quote on trends and styles at USD 38-210.
Nothing here needs a laboratory. A loupe, a gauge, a balance and a written sheet carry most of the quality a trends and styles buyer is paying for, which is why the protocol travels with the trays.
A station without a signature is a station that did not happen. Ours carries the inspector's initials per lot, and the sheet ships in the carton so a claim can be argued from paper, the detail a 400-piece run of trends and styles is judged on.

| Defect | Class | Likely cause | Fix at source |
|---|---|---|---|
| ('prong geometry', 'A prong that grips the girdle instead of the pavilion survives the showroom and fails the third ultrasonic clean. The seat has to be cut to the pavilion angle before the prongs close.') | Major | Bench or spec gap | Gauge per size and a retained reference piece |
| ('rhodium burn-off', 'A 0.05 micron rhodium layer reads white in the tray and shows yellow at the shank in six months of daily wear. Thickness, not bath chemistry, is the variable that matters.') | Major | Plating or casting prep | Porosity check before the plating bath |
| ('size-step drift', 'A run gauged at size 6 and estimated elsewhere ships a size 8 that measures 7.75. The mismatch shows up as a resize queue two weeks after launch.') | Critical or major | Component source | Incoming check on the component lot |
| Colour drift against the master | Major | Stone batching | Matched lot per tray, master stone on the bench |
| Sizing drift across the run | Major | Gauge not used | Go/no-go gauge on every size |
| Packing list mismatch | Minor to major | Dock reconciliation | Carton count signed before sealing |
Every row has a source upstream of the defect. Fixing the trends and style is a cost; fixing the row is a saving, and the difference is whether the cause is written down.
The first three rows account for most claims on trends and styles. They are also the three that a bench check catches before packing, which is why the sequence matters more than the sample size.
A defect taxonomy is only useful if the words match across the order, the inspection and the claim. Ours uses the six terms above on the quote, the QC sheet and the credit note, a detail that decides the reorder on trends and styles at USD 38-210.
One critical defect stops the lot and triggers a hundred percent check of the affected tray before anything ships. The buyer does not receive a percentage with a note attached; the tray is either reworked or held, the detail a 400-piece run of trends and styles is judged on.
A major defect rate above the plan triggers a second sample on the same lot before a decision. The second sample decides whether the cause is the run or the tray, and both outcomes are written on the sheet the same day, a detail that decides the reorder on trends and styles at USD 38-210.
A rejected tray is settled against the retained reference piece inside the same order cycle. If the difference shows on our retained piece we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that split is on the order before the deposit clears, the same figure we quote on trends and styles at USD 38-210.
Minor defects inside the plan ship with the count stated on the packing list, so the buyer's receiving team knows what to expect rather than discovering it. Stating a minor defect is cheaper than hiding one, which on a 400-piece run of trends and styles is the number the order carries.
The rule has to be signed before the run, because after the run it is a negotiation and the party holding the trends and styles has the leverage. Writing it into the purchase order is the whole protection.
Buyers sometimes ask for a zero-defect clause. We quote it, and we quote the inspection cost that makes it possible, because zero without a hundred percent check is a promise rather than a process, the same figure we quote on trends and styles at USD 38-210.
A claim handled in the same cycle costs a credit note. A claim handled after the season costs the relationship, which is the more expensive of the two, which on a 400-piece run of trends and styles is the number the order carries.
A third-party inspector adds independence, which matters when the factory is new to you and the order is large. It does not add specification: the inspector checks against the sheet you supply, so a vague sheet produces a vague report with a logo on it, the same figure we quote on trends and styles at USD 38-210.
The gap in most third-party reports is the retained reference. An inspector can measure a trends and style, but it cannot tell you whether the colour matches the master you approved, because it never saw the master. Send the reference piece with the inspection request.
Pay for an inspector on the first order above a few hundred pieces and on any order from a new factory. After two clean lots with the same spec, the money is better spent on your own receiving check and a gauge, the detail a 400-piece run of trends and styles is judged on.
AQL 1.0 for major and 2.5 for minor on the lots above 150 pieces, with zero acceptance on critical defects. Below 150 pieces the lot is small enough that a hundred percent check on the trends and style costs less than a sampling argument.
32 pieces on a 400-piece run, pulled across trays rather than from one. Every size in the lot gets a gauge pass regardless of the sample, because drift is a run property and not a trends and style property.
Yes. We schedule it, provide the trays and the sheet, and hold production until the report lands. Inspectors who arrive without the retained reference usually produce a report about appearance rather than about specification, a detail that decides the reorder on trends and styles at USD 38-210.
Stone loss, a prong that will not hold under load, a clasp that opens, or metal that fails a nickel or lead screen. One occurrence stops the lot; the others are counted against the plan, the same figure we quote on trends and styles at USD 38-210.
Both, at different stations. Porosity is checked before the plating bath, and plating thickness and colour are checked after it. An inspection that only happens at the end cannot tell you which of the two failed, which on a 400-piece run of trends and styles is the number the order carries.
Send the lot size and the defect history from your last order, and the reply comes back with the sampling plan, the six stations and the reject rule written for that lot rather than for a generic one, the detail a 400-piece run of trends and styles is judged on.
HOLYCOME is the export arm of Wuzhou HengliLai Jewelry Co., Ltd., a Wuzhou, Guangxi plant that has shipped since 2009 and produces about 60,000 pieces a month, trends and styles included. Export paperwork, the certificate pack and the packing list are prepared in-house, which is why the documents quoted on the order are the ones that travel with the carton. Reach the desk at service@holycome.com or WhatsApp +86 18078079070.
Related reading: Trends & Styles Supplier: 7 Supplier Checks Before You Pay - HOLYCOME Wholesale Sourcing Trade Show Sample: What the Quote Actually Covers - HOLYCOME
Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.
Contact on WhatsApp service@holycome.comWritten by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.
Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.
Reviewed for accuracy by our quality team before publication. Last updated .