Sizing Guide

Sizing Guide Landed Cost: HS Codes, Freight and the Invoice That Stops a Container

Sizing Guide Landed Cost: HS Codes, Freight and the Invoice That Stops a Container
Sizing Guide Landed Cost: HS Codes, Freight and the Invoice That Stops a Container

A retailer in Calgary placed a trial order and found the supplier could not produce a second lot to the same plating thickness. The order was not lost on price. It was lost on a specification nobody wrote down. This piece looks at sizing guide from the buyer's side of the table: what the promise means at the bench, what it costs to get it wrong, and how to write a brief a factory can be held to.

SECTION 01Six Questions That Reveal Whether a Supplier Can Actually Deliver

A supplier is a production system, not a price list. The questions that matter are the ones about repeatability, because your second order is what your customer judges you on.

We answer the six questions below with numbers and with a physical sample, and we expect to be asked for both.

SECTION 02What the Industry Standard Delivers, and Where It Breaks

The default offer in this category is a stock photo, a unit price and a thirty-day promise. That works for one order and stops working on the second, because a stock photo cannot specify court.

ComparisonCommon practiceWhat we holdWhy it matters
QuestionWeak answerWhat we provide
Capacity"plenty"monthly piece count per line
Repeatability"same quality"plating and weight tolerance
Traceability"we check everything"lot and rack record
Referenceslogosnamed buyers who will talk

SECTION 03How We Answer Them Before You Place an Order

Width and diameter consistency across a 200-piece run is the number we publish per lot. It is the one a buyer can check with a caliper and a loupe in ten minutes, and the one that decides whether a reorder is a formality or a negotiation.

  • Lot and rack reference on every carton
  • Court declared on the invoice, not assumed
  • One plated sample approved per rack before the run
  • Stone parcel photographed and hue band stated in writing

SECTION 04The Reorder Sheet We Hand Back

Every reorder comes back with the original sheet: alloy batch, stone parcel reference, plating rack number, setting team, measured width and diameter consistency across a 200-piece run. It is four lines and it removes the argument about what "the same" means.

Buyers who keep those four lines can audit a fifth lot in an afternoon. Buyers who do not are comparing two photographs and hoping.

SECTION 05Packaging and the First Thirty Seconds

The carton is the first physical impression. An anti-tarnish pouch, a cavity insert and a stone-side-up orientation cost a few cents and prevent most of the transit damage we see on bands.

Loose fill is the main cause of bent posts and scratched faces. It is cheaper than a cavity insert by about two cents a unit, which is the worst trade in the category.

SECTION 06Why We Publish the Numbers

Publishing width and diameter consistency across a 200-piece run and the plating micron figure is uncomfortable for a factory that expects to be judged on photographs. It is comfortable for a buyer who has to defend a reorder to a boss.

The number is the argument. A supplier who will not publish one is asking you to trust the photograph instead.

SECTION 07The Three Failure Modes We See Most

On bands the three failures that come back most often are inner-edge abrasion, seam porosity on the sizing joint, and width drift after polishing. Each has a root cause upstream of the bench, which is why sorting finished pieces never fixes the rate.

Prong wear traces to wire gauge and setting pressure. Stone tilt traces to the bearing surface being cut by hand instead of by burr. Plating burn-off traces to rack contact points, not to the tank.

SECTION 08Tolerance Stack: Where 0.1mm Becomes a Complaint

Tolerance compounds across operations. A casting that runs 0.15mm wide, a setting that shifts the stone 0.1mm, and a polish that removes 0.05mm of surface can put a band outside the size the customer ordered without any single step being out of specification.

That is why we hold the stack at the casting rather than at the finish. Tightening the last operation cannot recover tolerance that was already spent at the first.

SECTION 09The Reorder Sheet We Hand Back

Every reorder comes back with the original sheet: alloy batch, stone parcel reference, plating rack number, setting team, measured width and diameter consistency across a 200-piece run. It is four lines and it removes the argument about what "the same" means.

Buyers who keep those four lines can audit a fifth lot in an afternoon. Buyers who do not are comparing two photographs and hoping.

SECTION 10What to Send Us to Get a Real Quote

A sketch or reference photo, the metal and finish, the stone size and grade, the setting type, the target quantity and the tolerance you will accept. With those six fields we return a drawing and a price in three days.

Without them we can only quote a range, and a range is what turns into a dispute at delivery. We would rather send the drawing back with the tolerances printed on it than send a number that will not hold.

SECTION 11Why the Cheapest Sample Is the Most Expensive Decision

A sample that costs nothing is usually made from a stock tree with a stone the factory already had. It shows you the catalogue, not the production.

We charge samples at cost and credit them against the first order. It is a small amount of money that buys you a truthful answer about what your reorder will look like.

SECTION 12The Six Cost Lines and Which One Moves

Metal, stone, labour, plating, packaging and freight. On a fifty-piece run the first two carry roughly half the cost, labour about a quarter, and the rest the balance. A quote that undercuts the market by thirty per cent has moved one of the last four.

Plating and packaging are the cheapest to cut and the hardest for a buyer to see, which is exactly why they get cut. We publish the micron figure so the cut is visible before the order rather than after the first complaint.

SECTION 13What to Send Us to Get a Real Quote

A sketch or reference photo, the metal and finish, the stone size and grade, the setting type, the target quantity and the tolerance you will accept. With those six fields we return a drawing and a price in three days.

Without them we can only quote a range, and a range is what turns into a dispute at delivery. We would rather send the drawing back with the tolerances printed on it than send a number that will not hold.

SECTION 14What It Costs and How Long It Takes

Fifty pieces per design is the working minimum on sizing guide. A sample runs three to five days, bulk fifteen to twenty days under 500 pieces, and a custom mould twenty-five to thirty days from drawing approval. Payment is 30% deposit with the balance against the bill of lading copy.

If the order is below fifty, the setup cost per piece roughly doubles because the casting tree and the plating rack are fixed costs. That is arithmetic, not a policy to negotiate around.

ItemValueNote
MOQ50 pcs / designsizes and colours can be split
Sample3-5 daysone piece, approved before the run
Bulk lead time15-20 daysunder 500 pieces
Custom lead time25-30 daysfrom drawing approval
Payment30% / 70%balance against B/L copy
PortGuangzhou / Shenzhenexport from Wuzhou

SECTION 15Frequently Asked Questions

How long have you been manufacturing?

The Wuzhou operation has run since 2009, with casting, setting, polishing and plating on site rather than subcontracted. That matters because a subcontracted plating line is where thickness drifts.

Can I visit the factory?

Yes. Visitors are welcome in Wuzhou with two weeks' notice so the line you want to see is running production and not a cleaned-up demonstration cell.

What is your capacity per month?

Roughly 60,000 pieces across silver and gold lines, with moissanite setting capacity around 25,000 stones per month. Capacity is quoted per line, not as one number.

Will you sign an NDA and a quality agreement?

Yes. The quality agreement states the AQL per check point and the remedy, which is more useful than an NDA alone.

Can you produce a second lot identical to the first?

Yes, if we hold the four inputs: alloy batch, stone parcel, plating tank and setting team. The reorder sheet records all four, so the check happens against a document rather than against a memory.

What happens if the lot arrives outside the agreed tolerance?

Photograph the piece with a scale and reference the lot line. Above the agreed AQL we replace and cover freight; inside it we replace the affected units inside ten days.

SECTION 16About the Manufacturer

HOLYCOME by Wuzhou HengliLai Jewelry Co., Ltd. runs casting, setting, polishing and plating on one site in Wuzhou, Guangxi, the artificial gemstone cluster that supplies most of the trade. Monthly capacity is roughly 60,000 pieces across silver and gold lines. Buyers can reach the trade desk at service@holycome.com or on WhatsApp at +86 18078079070, and a factory visit can be arranged with two weeks' notice.

SECTION 17Next Step

If you are pricing sizing guide for a season, send the quantity per design, the stone grade you need and the date you need it on the shelf. We will return a drawing, a landed cost and a production date within three days, and a physical sample before you commit to a run. Samples are charged at cost and credited against the first order.

Related reading: Moissanite Care: Ultrasonic and Steam Cleaner Safety, Ring Size at Home: Five Measurement Methods That Actually Work, How to Read a GIA Grading Report Line by Line

E

Editorial Team

Senior editor at HOLYCOME, specializing in gemstone identification, jewelry manufacturing, and wholesale sourcing guides.

Looking for Wholesale Jewelry?

Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.

Contact on WhatsApp service@holycome.com

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .