Sizing Guide

Sizing Guide: How to Choose: A Buyer's Decision Tree in Five Steps - HOLYCOME

Sizing Guide: How to Choose: A Buyer's Decision Tree in Five Steps - HOLYCOME

Sizing Guide is a topic buyers meet twice: once when they plan the range, and once when a customer asks a question they cannot answer. This decision tree works for both.

SECTION 01Step one: define the job the piece has to do

Start with the buyer, not the product. A piece in this category for daily wear has a different tolerance than one for a gift box. Write the job in one sentence before you compare anything.

Daily wear means plating thickness and clasp strength. Gift means presentation and size certainty. Occasion means a scale that photographs well.

Sample by size run, not from one mixed tray. Defects cluster by size and by design, and a mixed sample hides both.

SECTION 02Step two: set the price ceiling before the spec

Work backward from the retail price. On Sizing Guide, the landed cost should sit at 25 to 35 percent of retail for wholesale programs, leaving room for the channel fee and the return allowance.

A specification that ignores the ceiling always overshoots. Set the ceiling, then choose metal and stone to fit it.

StepQuestionOutput
JobWho wears it, how often?One-sentence use case
CeilingWhat retail price?Landed cost target
PairWhich metal and stone?Price band and care story
NumbersWeight, size, microns?Verified sample spec
RecordIs it on the PO?Six-line spec

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Photograph the first article before the batch runs. A shifted seat or a short prong is cheapest to fix at one piece.

SECTION 03Step three: choose the material pair

Metal and stone are one decision, not two. Silver with moissanite, gold with lab grown, platinum with natural: each pair carries its own price band, care story and disclosure.

Write the pair, then check it against the ceiling. On Sizing Guide, most margin problems come from choosing the pair by taste and the ceiling by hope.

SECTION 04Step four: verify the three numbers

Gram weight, stone size and plating microns. These three decide the cost, the look and the durability. If a supplier cannot state all three, the specification is incomplete.

Verify them on a sample, not on a page. That is the whole of the Sizing Guide decision.

SECTION 05Step five: write it down

Turn the decision into six lines on the PO: metal and purity, gram weight, stone type and size, plating microns, size range and packaging.

A decision that is not written is a preference, and preferences do not survive a supplier change.

Price moves with three inputs: alloy, stone and plating. A quote that holds for ninety days is a quote that has priced those three honestly.

SECTION 06What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Start from the job, not the catalog.
  • Set the price ceiling before the spec.
  • Treat metal and stone as one pair.
  • Verify weight, size and microns on a sample.
  • Write six lines onto the PO.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

SECTION 07Frequently Asked Questions

What is the first question to ask about Sizing Guide?

Who wears it and how often. That answer sets the metal, the plating and the price ceiling.

Should I choose the stone or the metal first?

Together. The pair determines the price band and the care story; choosing one first usually breaks the other.

What landed cost should I target?

Twenty-five to thirty-five percent of retail for wholesale programs, depending on channel fees and return rate.

How do I check a supplier's numbers?

Weigh the sample, measure the stone, and ask for the plating spec. Three instruments settle it.

What if the sample passes but the lot does not?

The spec was never written. Put the six lines on the PO and inspect against them.

How many suppliers should I keep?

Two approved sources for the top three designs, one for the tail. The second source is what keeps pricing honest.

Send the Sizing Guide use case and retail price. We return a decision sheet with the material pair, the three numbers and the PO lines. See the full range at Sizing Guide and HOLYCOME.

The short version: specify the number, seal the sample, inspect against both. Everything else is negotiation.

E

Editorial Team

Senior editor at HOLYCOME, specializing in gemstone identification, jewelry manufacturing, and wholesale sourcing guides.

Looking for Wholesale Jewelry?

Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.

Contact on WhatsApp service@holycome.com

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .