Metal Guide

Metal Guide: Where Comes From: The Supply Chain Behind the Price - HOLYCOME

Metal Guide: Where Comes From: The Supply Chain Behind the Price - HOLYCOME

A Metal Guide price carries four supply steps: alloy, stone, casting and finishing. Knowing which step a supplier controls explains both the price and the risk.

SECTION 01Step one and two: alloy and stone

Alloy comes from a mill, usually in sheet, grain or tube. Stones come from cutting centers, and the cutting quality is set there, not at the setting bench. On Metal Guide, a cheap stone usually means a cheaper cut, not a cheaper rough.

Ask which mill and which cutting source. The answer tells you what can change without notice.

Put the gram weight per size on the PO, not an average. Cost and feel both follow weight, and an average hides the size that breaks the margin.

SECTION 02Step three: casting

Casting is either in-house or subcontracted. In-house means control over the alloy mix and the queue; subcontracted means a shared queue and a longer lead time in peak.

On Metal Guide, the casting arrangement is the single best predictor of peak-season reliability.

StepWho controlsRisk if opaque
AlloyMillPurity drift
StoneCutting centerGrade change
CastingFactory or subPeak delay
FinishingIn-house or shopColour variation
PlatingPlating shopThickness drift

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Sample by size run, not from one mixed tray. Defects cluster by size and by design, and a mixed sample hides both.

SECTION 03Step four: finishing and plating

Plating can be in-house or a plating shop. A plating shop serves many clients and its bath chemistry drifts; that drift is the source of colour variation between lots.

Ask for a colour sample per lot, and for the bath maintenance record if the volume justifies it.

SECTION 04Reading the chain in a quote

A quote that names the mill, the stone source, the casting arrangement and the plating shop is a quote you can audit. A quote that names none of them is a price with no chain behind it.

On Metal Guide, that transparency is worth more than a few percent on the unit price.

Freight is a planning line, not an emergency line. A carton that lands two weeks early costs less than one that lands two days late.

SECTION 05What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Ask which mill supplies the alloy.
  • Ask where the stones are cut.
  • Ask whether casting is in-house.
  • Ask for a colour sample per lot.
  • Audit the chain, not only the price.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

SECTION 06Frequently Asked Questions

Why does Metal Guide price vary between factories?

Different alloy sources, cutting quality and casting arrangements. The chain explains the price more than the labor rate does.

Does in-house casting matter?

In peak season, yes. It decides whether your order holds its slot.

Why does colour drift between lots?

Usually plating bath chemistry. A sample per lot catches it early.

Can I audit a supply chain?

At the level of names: mill, cutting source, casting, plating shop. Four answers make a quote auditable.

What is the biggest hidden risk?

A stone source change without notice. The lot looks similar and grades differently.

How do I know a supplier is reliable?

Two clean repeat lots and two on-time shipments. Before that it is a sample, not a supplier.

Send the Metal Guide spec. We return the four-step supply chain with the mill, stone source, casting and plating arrangement named. See the full range at Metal Guide and HOLYCOME.

The short version: specify the number, seal the sample, inspect against both. Everything else is negotiation.

E

Editorial Team

Senior editor at HOLYCOME, specializing in gemstone identification, jewelry manufacturing, and wholesale sourcing guides.

Looking for Wholesale Jewelry?

Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.

Contact on WhatsApp service@holycome.com

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .