Metal Guide

Metal Guide: Specification Sheet: The Eight Fields That Prevent Disputes - HOLYCOME

Metal Guide: Specification Sheet: The Eight Fields That Prevent Disputes - HOLYCOME

A Metal Guide spec sheet is not paperwork. It is the document every claim, listing and QC decision refers back to. Eight fields make it usable.

SECTION 01Fields one to three: identity

SKU, product name and metal with purity. On Metal Guide, the metal line must carry the stamp value, not a marketing word. 'Silver' is not a specification; '925 sterling, 2.1 g' is.

Add the maker's mark if the channel requires it.

Ask for the plating thickness in microns, then test the contact points on the first lot. A thirty-second cloth rub shows colour transfer before a customer does.

SECTION 02Fields four to six: the physical numbers

Gram weight per size, stone type with size and grade, and dimensions. These three decide cost, look and durability.

On Metal Guide, a spec without a per-size weight will drift at the first size change, and the quote will drift with it.

FieldExampleUsed by
SKUHC-RG-1042Listing, warehouse
Metal and purity925 sterlingClaim, QC
Gram weight2.1 g size 6Cost, QC
Stone6.5 mm moissaniteClaim, QC
DimensionsBand 1.8 mmDesign, repair
Plating0.8 micron rhodiumDurability claim
ComplianceNickel pass, origin CNImport, platform
Versionv3, 2026-11All of the above

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Photograph the first article before the batch runs. A shifted seat or a short prong is cheapest to fix at one piece.

SECTION 03Fields seven and eight: finish and compliance

Plating type and thickness in microns, plus the compliance note: nickel, Prop 65 and country of origin.

Those two lines are what make a listing defensible when a platform or a customer asks a direct question.

SECTION 04Keeping the sheet alive

Version every sheet and attach the version to the PO. When a stone or a supplier changes, the version changes.

On Metal Guide, most listing errors trace to a sheet that was updated in one place and not another.

The specification is the product. Two pieces built to the same six lines are the same product even when the price differs; two built to different lines are not.

SECTION 05What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Write the stamp value, not a marketing word.
  • Give weight per size.
  • State stone size and grade.
  • State plating in microns.
  • Version the sheet with the PO.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

SECTION 06Frequently Asked Questions

What must a Metal Guide spec sheet include?

SKU, metal and purity, gram weight per size, stone type and size, dimensions, plating microns, compliance note and version.

Why per-size weight?

Because cost follows weight. An average hides the size where the metal line breaks the margin.

Who writes the sheet?

The factory drafts from the lot, the buyer approves against the PO. Two signatures.

How often should it change?

Whenever a material, a supplier or a stone grade changes. Every change gets a version.

Is a spec sheet enough for a listing?

It is the source. The listing still needs the channel-specific fields and the disclosure wording.

How many suppliers should I keep?

Two approved sources for the top three designs, one for the tail. The second source is what keeps pricing honest.

Send the a SKU in this category list. We return an eight-field spec sheet template with the version block and the QC reference. See the full range at Metal Guide and HOLYCOME.

None of this is exotic. It is a document, a measurement and a date, repeated until it becomes a process.

E

Editorial Team

Senior editor at HOLYCOME, specializing in gemstone identification, jewelry manufacturing, and wholesale sourcing guides.

Looking for Wholesale Jewelry?

Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.

Contact on WhatsApp service@holycome.com

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .