Metal Guide

Metal Guide Wholesale: MOQ, Mixed Designs and the Real First Order - HOLYCOME

Metal Guide Wholesale: MOQ, Mixed Designs and the Real First Order - HOLYCOME

SECTION 01MOQ, Mixed Designs and the Real First Order

Last February, a US fine jewelry retailers and pawn-adjacent resellers placed 120 metal Guide against a sample signed in June. The first container landed with 9 pieces that failed on stamp accuracy alone, and USD 30-100 landed on the buyer's P&L before a single unit sold.

Nobody on that bench was careless. They were working to a spec that existed only in a photograph, and stamp accuracy is what a photograph fails to define. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

Metal Guide wholesale product photo from the HOLYCOME line in Wuzhou

The fix cost about 21 seconds per metal Guide and removed the credit note entirely. That is the whole economics of a spec sheet, and it is why we write one on every quote. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

SECTION 02What US buyers Check Before They Sign

A quote for metal Guide usually states carat weight or metal type, and stops there. The four points below are what actually decide whether a run sells through or comes back. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Stamp Accuracy on metal GuideInspected visually at the trayGauntlet check on every piece, limit written in the specReturns inside 60 days of wear
Alloy Color Drift on metal GuideBatch dependent, not loggedThickness and tension logged per lotComplaint after the second season
Solder Joint Porosity on metal GuideEstimated from nominalGauged per size with go/no-go toolsResize queue and reship cost
Tolerance stack-up on metal GuideQuote states nominal onlyWorst-case band published per SKUFreight and duty drift

Each line above is a gauge check, not a marketing claim. A factory that cannot state them in numbers is quoting an opinion about metal Guide. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

SECTION 03Where USD 45-320 Per Piece Actually Goes

At USD 45-320 per piece there is no room for hidden cost. The table shows where the money sits and which line a supplier can actually compress. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

Metal Guide close-up of setting and finish, HOLYCOME factory sample
Cost lineShareWhat moves it
Base metal or alloy for metal Guide30%Alloy choice and casting yield
Stone or melee for metal Guide20%Sieve range and lot batching
Setting and finishing labor for metal Guide19%Jig design and bench minutes
Plating, polish and QC for metal Guide12%Per-tray versus per-piece checks
Packaging and freight for metal Guide19%Box grade and DDP versus FOB

A factory that cannot state its bench minutes per piece has never costed its own line. Ask for minutes and for the reject rule, not for a discount. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

SECTION 04The Three Failures We See Most in Incoming Samples

stamp accuracy

A 14K stamp on 13.6K metal is a legal exposure, not a cosmetic one. Assay per lot is the only defensible check.

In a 120-piece run this typically shows on 8 of pieces. Catching it means measuring assay within 0.3K of the stamp at the tray level, not inspecting the finished carton.

alloy color drift

Two alloy lots of 14K rose can read peach and copper under the same light. Holding a master color chip per order keeps a collection coherent.

The commercial effect is refining loss plus a legal stamp correction, typically USD 15-28 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return.

solder joint porosity

A sizing joint soldered with too much flux pits after polish and cracks in wear. Joint inspection belongs in the final QC, not the bench.

Our countermeasure is a gauge and a written limit. It adds about 21 seconds per piece and removes the defect from the run rather than from the carton.

SECTION 05MOQ, Mixed Designs and the Real First Order

Buyers who have run three programs on metal Guide know this instinctively; first-time buyers learn it the expensive way.

The buyers who get the most out of gold pieces treat the first order as a measurement, not as a purchase. They buy a small run, measure the four numbers that matter, and then commit.

We support it directly on metal Guide: a 50-piece test run per design, the same gauge standard as a bulk order, and the same retained tray. Small does not have to mean loose.

SECTION 06How a Repeat Order Gets Built

Nothing in this sequence is unusual, and that is the point. Each step exists because skipping it produced a specific failure on a previous order. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

  1. Spec sheet signed before casting: cast or hand-finished, tolerances, plating thickness and packing format.
  2. Sample in 3-5 working days from stock components, or about 20 days if a new model is required.
  3. Production photos at three checkpoints: raw cast, post-polish, post-set, with buyer approval at each.
  4. Bulk in 15-20 days under 500 pieces; custom tooling runs 25-30 days.
  5. Pre-shipment QC report with per-tray counts and a retained reference tray for disputes.

Reorders inside this sequence run 12-15 days because the model, the gauge set and the signed spec stay in our system. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

SECTION 07Alloy, Karat and the Cost of a Color Change

On metal Guide, the difference between a 40-day order and a 90-day order is usually two signatures, not a factory delay.

Buyers who get this wrong on gold pieces usually get it wrong in the first order and correct it in the second. The cost of that correction is rarely the money; it is the four to six weeks of shelf time lost while a replacement run of gold pieces is scheduled behind other orders.

Our approach is to write the rule into the metal Guide spec sheet before casting, then test it on the first tray. A rule that only exists in an email is not a rule, and a rule that is not tested is a hope.

SECTION 08The Sample Approval That Survives Production

The figure below is what we quote for metal Guide, and it is deliberately narrower than the market average.

The commercial version of this question for gold pieces is simple: what does a failure cost the buyer, and who pays it. In our terms the answer is a replacement inside the same order cycle, with the retained reference tray as the arbiter.

That clause matters more than a discount on gold pieces. A 4% lower unit price disappears on the first rejected tray; a written responsibility clause does not.

SECTION 09Carton Cube, Duty and the Freight Line That Surprises Buyers

A buyer who understands this about metal Guide negotiates differently, and usually negotiates less.

The commercial version of this question for gold pieces is simple: what does a failure cost the buyer, and who pays it. In our terms the answer is a replacement inside the same order cycle, with the retained reference tray as the arbiter.

That clause matters more than a discount on gold pieces. A 4% lower unit price disappears on the first rejected tray; a written responsibility clause does not.

SECTION 10What This Means for a First Order

A first order of 50 pieces per design is a measurement, not a purchase. It shows how assay within 0.3K of the stamp and color match to the master chip behaves on this line and whether the QC sheet matches the carton. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

Six weeks of testing is cheaper than a season of returns on metal Guide. That is the entire argument for a small first order. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

SECTION 11Freight, Duty and the Arrival Check

Export runs through Guangzhou or Shenzhen. Air freight lands in 5-8 days on the US west coast and 7-10 on the east. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

For a first order, DDP matters more than the freight rate. The surprise is the duty line, not the per-kilo charge. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

Check the count, the weight and assay within 0.3K of the stamp and color match to the master chip before the carton goes to the shelf. Twenty minutes at receiving saves a season of returns. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

SECTION 12Frequently Asked Questions

What is the minimum order for metal Guide?

50 pieces per metal Guide. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 we cannot keep the gauge check independent of the shift, which is the part buyers actually pay for on metal Guide.

How long does a reorder of the same metal Guide take?

12-15 days for metal Guide, because the model, the gauge set and the signed spec stay in our system. A first run is longer: 3-5 days for a stock-component sample, about 20 days if a new model is needed, then 15-20 days for bulk under 500 pieces.

Do you supply certificates for metal Guide?

assay report per lot for metal Guide. Below that threshold we supply a batch report plus per-piece measurement of assay within 0.3K of the stamp, which is what most resellers need at the counter.

What finish do you use on metal Guide, and how thick is it?

Rhodium at 0.20 micron minimum on white metal Guide, with a palladium strike layer so wear-through reads white rather than yellow. Thickness is logged per lot and appears on the QC sheet, not only in the brochure.

How do you handle a rejected tray of metal Guide?

We replace or credit inside the same order cycle. The retained reference tray decides: if stamp accuracy shows on our retained metal Guide we own it, and if it appeared in transit we split the assay cost and file with the carrier. A typical exposure on metal Guide is refining loss plus a legal stamp correction, typically USD 15-28 per piece.

SECTION 13Next Step

Put your current quote beside ours on assay within 0.3K of the stamp and color match to the master chip, plating thickness, dimensional tolerance and the reject rule. The comparison usually settles it quickly. That is the figure we hold for metal Guide at USD 45-320 per piece, and it does not move inside the order window.

HOLYCOME is operated by Wuzhou HengliLai Jewelry Co., Ltd., a factory in Wuzhou, Guangxi, producing since 2009 at roughly 60,000 pieces a month. Contact service@holycome.com or WhatsApp +86 18078079070.

Related reading: Buying Guides Supplier: Sample to Container: The Real Calendar - HOLYCOME Sizing Guide Supplier: Alloy, Karat and the Cost of a Color Change - HOLYCOME

E

Editorial Team

Senior editor at HOLYCOME, specializing in gemstone identification, jewelry manufacturing, and wholesale sourcing guides.

Looking for Wholesale Jewelry?

Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.

Contact on WhatsApp service@holycome.com

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .