In January, a US buyer of metal Guide ordered 50 metal Guide and asked for the same cast or hand-finished as a competitor's sample. What arrived matched the photo and missed the drawing, and 13 pieces had to be reworked at the buyer's expense, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
The defect did not surprise us. Stamp accuracy is the predictable output of a run where nobody wrote the tolerance down, and it is the first measurement we take on an incoming metal Guide, priced at USD 56-400 for the 50-piece Made to Order run.
We did not discount the quote. We changed the gauge, the seat cut, the plating log and the tray rule, and the second run shipped with zero rejects on assay within 0.3K of the stamp and color match to the master chip, and the Made to Order quote for it sits at USD 56-400.
Made-to-order is a different production line, not a slower version of stock. It starts with a signed drawing, then a wax or resin model, then a casting, then setting, then finish, and each stage can fail on its own, quoted at USD 56-400 per piece in single-piece foam box.
Twenty days is realistic for a new metal Guide when the model exists and only the stone changes. A new model adds a day for the CAD, a day for the print, and a day for the buyer to approve the render before metal is committed, and at USD 56-400 for 50 pieces that is the number the buyer signs.
The risk sits in approval, not in the bench. A buyer who approves a render on a phone screen and rejects the casting has bought a prototype, not a product. We send the render at 1:1 scale with a millimetre grid for that reason, the figure being USD 56-400 for a 50-piece run.

Two alloy lots of 14K rose can read peach and copper under the same light. Holding a master color chip per order keeps a collection coherent, which is USD 56-400 on the Made to Order schedule.
Our countermeasure is a gauge and a written limit. It adds about 21 seconds per piece and removes the defect from the run rather than from the carton, on a 50-piece Made to Order order at USD 56-400.
A sizing joint soldered with too much flux pits after polish and cracks in wear. Joint inspection belongs in the final QC, not the bench, which is how the Made to Order account reads it at USD 56-400.
In a 50-piece run this typically shows on 17 of pieces. Catching it means measuring assay within 0.3K of the stamp at the tray level, not inspecting the finished carton, which is how the Made to Order account reads it at USD 56-400.
A 14K stamp on 13.6K metal is a legal exposure, not a cosmetic one. Assay per lot is the only defensible check, quoted at USD 56-400 per piece in single-piece foam box.
The commercial effect is refining loss plus a legal stamp correction, typically USD 15-28 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, with IGI report and single-piece foam box stated on the same sheet.
Price is the first thing compared and the last thing that matters. These four measurements decide the return rate on metal Guide, and three of them cost nothing to specify, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
| Spec point | Common trade output | HOLYCOME standard | Cost if missed |
|---|---|---|---|
| Clasp spring life | Sampled by hand | Cycled 500 times on a jig per lot | Detach claim and brand damage |
| Prong tension and seat depth | Checked by feel at the bench | Pull-tested per piece, seat depth written on the sheet | Stone loss and total replacement |
| Hallmark depth and placement | Stamped where it fits | Fixed position, depth measured so it never breaks the shank | Customs query and remaking |
| Solder flow at the joint | Not inspected | Joint inspected under 10x before setting | Crack at the seam in transit |
Each line is a gauge, not a slogan. A supplier who cannot quote a number for stamp accuracy is quoting an opinion about metal Guide, which is how the Made to Order account reads it at USD 56-400.
The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 50-piece Made to Order order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, shipped as single-piece foam box and certified IGI report.
Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 56-400 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.
Packing follows the single-piece foam box format at 50 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, which the Made to Order file records at USD 56-400 in single-piece foam box.
Certification is IGI report for the lots that carry it, with a batch report and per-piece measurement of assay within 0.3K of the stamp for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, which is USD 56-400 on the Made to Order schedule.
A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, on a 50-piece Made to Order order at USD 56-400.
The Made to Order price of 50 pieces splits as below. The line buyers challenge is labor, and it is the line that decides the second season, on a 50-piece Made to Order order at USD 56-400.
| Cost line | Share | What moves it |
|---|---|---|
| Base metal or alloy for metal Guide | 34% | Alloy choice and casting yield |
| Stone or melee for metal Guide | 25% | Sieve range and lot batching |
| Setting and finishing labor for metal Guide | 22% | Jig design and bench minutes |
| Plating, polish and QC for metal Guide | 15% | Per-tray versus per-piece checks |
| Packaging for metal Guide | 4% | single-piece foam box |
Break the USD 56-400 quote into these five lines and the comparison stops being rhetorical.
The figure below is what we quote for metal Guide, and it is deliberately narrower than the market average, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
Three numbers decide it for metal Guide: the tolerance band, the inspection density and the responsibility clause. Write all three down and the rest of the negotiation is arithmetic. Leave any of them out and it becomes a discussion about intent, and the Made to Order quote for it sits at USD 56-400.
We send a one-page sheet with every metal Guide quote that states those three, plus the retained-tray rule. Buyers who compare on it usually find that the gap between suppliers is smaller than the gap between the specs they were comparing, certified IGI report and packed single-piece foam box at 50 pieces.
Most metal Guide disputes we arbitrate trace back to this line, not to the defect itself, which is how the Made to Order account reads it at USD 56-400.
There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on metal Guide and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly, and at USD 56-400 for 50 pieces that is the number the buyer signs.
We would rather lose a first order of metal Guide on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high, quoted at USD 56-400 per piece in single-piece foam box.
A test run at 50 pieces tells you three things: whether stamp accuracy is controlled, whether packing survives freight, and whether the count is honest, on a 50-piece Made to Order order at USD 56-400.
Put the reject rule in writing before the deposit. The Made to Order conversation after arrival is shorter when the rule is already on the order, quoted at USD 56-400 per piece in single-piece foam box.
Air lands in 5-8 days to the US west coast and sea takes three times the transit. At USD 56-400 per piece the choice is a cash-flow decision.
DDP is available for US accounts that want duty and clearance on our side, and it removes the invoice that arrives after the carton clears, and at USD 56-400 for 50 pieces that is the number the buyer signs.
On arrival, weigh a tray and measure ten pieces. Anything outside the band is a claim with evidence rather than a difference of opinion, which is USD 56-400 on the Made to Order schedule.
On 50 pieces of metal Guide the calendar starts at the signed spec, not at the deposit, and it ends with single-piece foam box on a pallet, certified IGI report and packed single-piece foam box at 50 pieces.
A 50-piece first order at USD 56-400 is a measurement of assay within 0.3K of the stamp, not a commitment to the range.
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, and the Made to Order quote for it sits at USD 56-400.
With the model, the gauge set and the signed spec already in our system, a repeat is 12-15 days; a first run is 3-5 days for a stock-component sample and about 20 days when a new model is needed, which is USD 56-400 on the Made to Order schedule.
Rhodium at 0.20 micron minimum on white metal Guide, with a palladium strike layer so wear-through reads white rather than yellow. Vermeil runs at 3 microns over sterling and is logged per lot, priced at USD 56-400 for the 50-piece Made to Order run.
Every unit goes into a foam-backed pouch, then the single-piece foam box, then the outer carton at 50 pieces. The packing list carries the SKU, the size and the stone size so receiving can check without opening every box, quoted at USD 56-400 per piece in single-piece foam box.
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, and the Made to Order quote for it sits at USD 56-400.
Send a photo or a drawing of the piece you want in single-piece foam box. We answer with a price, a calendar and the four measurements above, certified IGI report and packed single-piece foam box at 50 pieces.
The factory behind metal Guide here is Wuzhou HengliLai Jewelry Co., Ltd., operating since 2009 in Wuzhou, Guangxi, at roughly 60,000 pieces a month. Reach the export desk at service@holycome.com or +86 18078079070 on WhatsApp, the figure being USD 56-400 for a 50-piece run.
Related reading: Buying Guides Private Label Carton: Carton Cube, Duty and the Freight Line That Surpr - HOLYCOME Buying Guides Q4 Holiday Stock: MOQ, Mixed Designs and the Real First Order - HOLYCOME
Wuzhou HengliLai Jewelry Co., Ltd. - Professional gemstone and jewelry manufacturer in Wuzhou, China. OEM/ODM services, factory-direct pricing, low MOQ.
Contact on WhatsApp service@holycome.comWritten by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.
Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.
Reviewed for accuracy by our quality team before publication. Last updated .